View EVAL-AD1994EB_1238160.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Audio Switching Amplifier AD1994
FEATURES
Integrated stereo modulator and power stage <0.005% THD + N 105 dB dynamic range (A-weighted) 2 x 25 W output power (6 , 10% THD + N) 1 x 50 W output power (3 , 10% THD + N) RDS-ON < 0.3 (per transistor) PSRR > 65 dB On-off-mute pop noise suppression EMI optimized modulator Short-circuit protection Overtemperature protection Low cost DMOS process
GENERAL DESCRIPTION
The AD1994 is a 2-channel, bridge tied load (BTL), switching audio power amplifier with integrated - modulator. The modulator accepts a single-ended, analog input signal and converts it to a switching waveform to drive speakers directly. One of the two modulators can control both output stages providing twice the current and almost twice the efficiency for single-channel applications. Both modulators can also control external power devices for arbitrarily high output power. A digital, microprocessor-compatible interface provides control of reset, mute, and PGA gain, as well as feedback signals for thermal and overcurrent error conditions. The output stage can operate over a power supply voltages range of 8 V to 20 V. The analog modulator and digital logic operate from a 5 V supply.
APPLICATIONS
Advanced televisions Compact multimedia systems Minicomponents
FUNCTIONAL BLOCK DIAGRAM
FEEDBACK NETWORK
NFL+
PGA1
PGA0 AVDD
NFL-
DVDD
PVDD
AD1994
AINL PGA - MODULATOR A1 A2 OUTL+
MOD_FILT
ORDER REDUCER
B1 LEVEL SHIFTER AND DEAD TIME CONTROL B2 H-BRIDGE C1 C2 OUTL-
AINR
PGA
- MODULATOR
OUTR+
CLKI CLKO OSCILLATOR
MODE CONTROL LOGIC AND POP/CLICK SUPPRESSION D1
REF_FILT
VOLTAGE REFERENCE
D2
OUTR-
MUTE
RESET
NFR-
DCTRL2
DCTRL1
AGND
DCTRL0
ERR2
ERR1
ERR0
NFR+
PGND FEEDBACK NETWORK
05775-001
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved.
AD1994 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 5 ESD Caution.................................................................................. 5 Pin Configuration and Function Descriptions............................. 6 Typical Performance Characteristics ............................................. 8 Theory of Operation ...................................................................... 15 Overview...................................................................................... 15 - Modulator............................................................................ 15 MUTE and RESET ..................................................................... 15 Mono Mode................................................................................. 16 Modulator Mode ........................................................................ 16 Gain Structure............................................................................. 16 Power Stage ................................................................................. 17 Clocking....................................................................................... 18 Protection Circuits and Error Reporting ................................ 19 Application Circuits ....................................................................... 20 Outline Dimensions ....................................................................... 21 Ordering Guide .......................................................................... 21
REVISION HISTORY
2/06--Revision 0: Initial Version
Rev. 0 | Page 2 of 24
AD1994 SPECIFICATIONS
Test conditions, unless otherwise specified. Table 1.
Parameter SUPPLY VOLTAGES AVDD DVDD PVDD AMBIENT TEMPERATURE LOAD IMPEDANCE CLOCK FREQUENCY PGA GAIN MEASUREMENT BANDWIDTH Ratings 5V 5V 12 V 25C 6 12.288 MHz 0 dB 20 Hz to 20 kHz
Table 2.
Parameter RDS-ON Per High-Side Transistor Per Low-Side Transistor MAXIMUM CURRENT THROUGH OUTx THERMAL WARNING ACTIVE THERMAL SHUTDOWN ACTIVE RESTORE TEMPERATURE AFTER THERMAL SHUTDOWN Min Typ 260 210 5 135 150 120 Max 355 265 Unit m m A C C C Test Conditions/Comments T = 25C T = 25C Peak Die temperature Die temperature Die temperature
Table 3. Performance Specifications
Parameter TOTAL HARMONIC DISTORTION AND NOISE (THD + N) Typ 0.003 0.006 0.01 0.02 105 105 -100 Unit % % % % dB dB dB Test Conditions/Comments PGA = 0 dB, PO = 1 W, 1 kHz PGA = 6 dB, PO = 1 W, 1 kHz PGA = 12 dB, PO = 1 W, 1 kHz PGA = 18 dB, PO = 1 W, 1 kHz 1 kHz, A-weighted, 0 dB referred to 1% THD + N output 1 kHz, A-weighted, -60 dB referred to 1% THD + N output PGA = 0 dB, PO = 5 W, 1 kHz
SIGNAL-TO-NOISE RATIO (SNR) DYNAMIC RANGE (DNR) CROSSTALK (LEFT-TO-RIGHT OR RIGHT-TO-LEFT)
Table 4. DC Specifications
Parameter INPUT IMPEDANCE OUTPUT DC OFFSET Typ 20 4 Unit k mV Test Conditions/Comments AINL, AINR input pins Independent of PGA setting
Rev. 0 | Page 3 of 24
AD1994
Table 5. Power Supplies
Parameter ANALOG SUPPLY, AVDD DIGITAL SUPPLY, DVDD POWER TRANSISTOR SUPPLY, PVDD RESET/POWER-DOWN CURRENT AVDD DVDD PVDD QUIESCENT CURRENT AVDD DVDD PVDD OPERATING CURRENT AVDD DVDD PVDD Min 4.5 4.5 6.5 Typ 5.0 5.0 8 to 20 0.6 7.5 19 20 5.5 30 20 5.5 218 27 7 260 Max 5.5 5.5 22.5 1 11 40 Unit V V V A A A mA mA mA mA mA mA RESET held low 5V 5V 12 V Inputs grounded, nonoverlap = minimum 5V 5V 12 V VIN = 1 V rms, RL = 6 , PO = 1 W 5V 5V 12 V Test Conditions/Comments
Table 6. Digital I/O
Parameter INPUT LOGIC HIGH INPUT LOGIC LOW OUTPUT LOGIC HIGH OUTPUT LOGIC LOW LEAKAGE CURRENT ON DIGITAL OUTPUTS Min 2.0 2.4 0.4 10 Typ Max 0.8 Unit V V V V A Test Conditions/Comments
@ 4 mA @ 4 mA
Table 7. Digital Timing
Parameter tMD tUD Typ 10 34 Unit s s Test Conditions/Comments Delay after MUTE is asserted until output stops switching Delay after MUTE is deasserted until output starts switching
tMD
MUTE
tUD
OUTx
Figure 2. Mute and Unmute Delay Timing
Rev. 0 | Page 4 of 24
05775-002
AD1994 ABSOLUTE MAXIMUM RATINGS
Table 8.
Parameter AVDD, DVDD to AGND, DGND PVDDx to PGNDx 1 AGND to DGND to PGNDx AVDD, to DVDD Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Thermal Resistance JA JC (at the Exposed Pad Surface) JB (on JEDEC Standard PCB)
1
Rating -0.3 V to +6.5 V -0.3 V to +30.0 V -0.3 V to +0.3 V -0.5 V to +0.5 V -40C to +85C -65C to +150C 150C 19.2C/W 0.9C/W 9.7C/W
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Including any induced voltage due to inductive load.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 5 of 24
AD1994 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
MONO_EN NFL+ NFL- NC AINL NC MOD_FILT AVDD AGND REF_FILT NC AINR NC NFR- NFR+ MOD_EN 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
PGND1 PGND1 PGND1 OUTL+ OUTL+ OUTL+ PVDD1 PVDD1 PVDD1 PVDD1 OUTL- OUTL- OUTL- PGND1 PGND1 PGND1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PIN 1 INDICATOR
AD1994
TOP VIEW (Not to Scale)
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
PGND2 PGND2 PGND2 OUTR+ OUTR+ OUTR+ PVDD2 PVDD2 PVDD2 PVDD2 OUTR- OUTR- OUTR- PGND2 PGND2 PGND2
ERR2 ERR1 MODL/ERR0 MODR/DCTRL2 DCTRL1 DCTRL0 DGND DVDD DVDD DGND CLKI CLKO MUTE RESET PGA1 PGA0
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
NC = NO CONNECT
Figure 3. Pin Configuration
Table 9. Pin Function Descriptions
Pin No. 1, 2, 3 4, 5, 6 7, 8, 9, 10 11, 12, 13 14, 15, 16 17 18 19 20 21 22 23, 26 24, 25 27 28 29 30 31 32 33, 34, 35 36, 37, 38 39, 40, 41, 42 43, 44, 45 46, 47, 48 49 Mnemonic PGND1 OUTL+ PVDD1 OUTL- PGND1 ERR2 ERR1 MODL/ERR0 MODR/DCTRL2 DCTRL1 DCTRL0 DGND DVDD CLKI CLKO MUTE RESET PGA1 PGA0 PGND2 OUTR- PVDD2 OUTR+ PGND2 MOD_EN In/Out O O O O O I/O I I Description Negative Power Supply. Used for the A2 and B2 high power transistors. Output of Transistor Pair A1 and A2. Positive Power Supply. Used for the A1 and B1 high power transistors. Output of Transistor Pair B1 and B2. Negative Power Supply. Used for the A2 and B2 high power transistors. Active Low Thermal Shutdown. Active Low Thermal Warning Error Output. Active Low Overcurrent Error Output/Modulator Output Left. Nonoverlap Time Setting MSB/Modulator Output Right. Nonoverlap Time Setting. Nonoverlap Time Setting LSB. Negative Power Supply for Low Power Digital Circuitry. Positive Power Supply for Low Power Digital Circuitry. Clock Input for 256 x fS Audio Modulator Clock. Inverted Version of CLKI for Use with an External XTAL Oscillator. Active Low Mute Input. Active Low Reset Input. PGA Gain Control MSB. PGA Gain Control LSB. Negative Power Supply for High Power Transistors C2 and D2. Output of Transistor Pair D1 and D2. Positive Power Supply for High Power Transistors C1 and D1. Output of Transistor Pair C1 and C2. Negative Power Supply for High Power Transistors C2 and D2. Modulator Mode Enable Pin when Pulled to Logic High.
Rev. 0 | Page 6 of 24
I O I I I I O O I
05775-003
AD1994
Pin No. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Mnemonic NFR+ NFR- NC AINR NC REF_FILT AGND AVDD MOD_FILT NC AINL NC NFL- NFL+ MONO_EN In/Out I I I O Description Right Channel Negative Feedback--Noninverting Input. Right Channel Negative Feedback--Inverting Input. No Connection--Should Be Left Floating. Analog Input for Right Channel. No Connection--Should Be Left Floating. Filter Pin for Band Gap Reference--Should Be Bypassed to AGND. Negative Power Supply for Low Power Analog Circuitry. Positive Power Supply for Low Power Analog Circuitry. Modulator Filter Pin--Used to Set Time Constant of Modulator Order Reduction Circuit. No Connection--Should Be Left Floating. Analog Input for Left Channel. No connection--Should Be Left Floating. Left Channel Negative Feedback--Inverting Input. Left Channel Negative Feedback--Noninverting Input. Mono Mode Enable Pin--When Pulled Up to Logic High.
O O I I I
Rev. 0 | Page 7 of 24
AD1994 TYPICAL PERFORMANCE CHARACTERISTICS
0 0
POWER (dBFS: 0dB = Power at which THD = 1% (13.8W))
-40 -60 -80 -100 -120 -140 -160
POWER (dBFS: 0dB = Power at which THD = 1% (13.8W))
05775-004
-20
-20 -40 -60 -80 -100 -120 -140 -160
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 4. 1 W Output Power into 4 Load
0 0
Figure 7. -60 dBFS Output Power into 4 Load
POWER (dBFS: 0dB = Power at which THD = 1% (10.1W))
-40 -60 -80 -100 -120 -140 -160
POWER (dBFS: 0dB = Power at which THD = 1% (10.1W))
-20
-20 -40 -60 -80 -100 -120 -140 -160
05775-005
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 5. 1 W Output Power into 6 Load
0 0
Figure 8. -60 dBFS Output Power into 6 Load
POWER (dBFS: 0dB = Power at which THD = 1% (7.9W))
-40 -60 -80 -100 -120 -140 -160
POWER (dBFS: 0dB = Power at which THD = 1% (7.9W))
-20
-20 -40 -60 -80 -100 -120 -140 -160
05775-006
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 6. 1 W Output Power into 8 Load
Figure 9. -60 dBFS Output Power into 8 Load
Rev. 0 | Page 8 of 24
05775-009
05775-008
05775-007
AD1994
20 0 -40 -50 0.1 -60 -70
POWER (dB, Relative to 500mW) (Output Power in the 19k and 20k Tones)
0 -20 -40
-60 -80 -100 -120 -140
0.01
-80 -90
0.001
-100 -110
05775-010
100
1k FREQUENCY (Hz)
10k
100
1k FREQUENCY (Hz)
10k
Figure 10. IMD for 19 kHz/20 kHz Twin-Tone Stimulus with 1 W Total Output Power
40 35 30 PGA GAIN = 18dB
Figure 13. THD vs. Frequency, 1 W Output Power into 4 Load, PVDD = 12 V
0 -40 -50
PGA GAIN = 12dB PGA GAIN = 6dB
AMPLIFIER GAIN (dB)
0.1
-60 -70
25 20 15 10 5 0
PGA GAIN = 0dB
0.01
-80 -90
0.001
-100 -110
100
1k FREQUENCY (Hz)
10k
FREQUENCY (Hz)
Figure 11. Amplifier Gain vs. Frequency, 6 Load, PVDD = 12 V
0
Figure 14. THD vs. Frequency, 1 W Output Power into 6 Load, PVDD = 12 V
0 -40 -50 0.1 -60 -70
SIGNAL IN IDLE CHANNEL (dB, Relative to Driven Channel Signal)
-40
-60 L CHANNEL DRIVEN, R CHANNEL IDLE -80
0.01
-80 -90
0.001 -100 L CHANNEL IDLE, R CHANNEL DRIVEN
05775-012
-100 -110
100
1k FREQUENCY (Hz)
10k
100
1k FREQUENCY (Hz)
10k
Figure 12. Channel Separation vs. Frequency, Driven Channel Has 1 W Output Power into 6 Load
Figure 15. THD vs. Frequency, 1 W Output Power into 8 Load, PVDD = 12 V
Rev. 0 | Page 9 of 24
05775-015
-120
0.0001
-120
THD (dB, Relative to Fundamental)
-20
THD (%)
05775-014
100
1k
10k
05775-011
0.0001
-120
THD (dB, Relative to Fundamental)
THD (%)
05775-013
0.0001
-120
THD (dB, Relative to Fundamental)
THD (%)
AD1994
100 0 100 0 -10 10 -20 -30 1 -40 -50 0.1 -60 -70 THD + N 0.01 THD 1 OUTPUT POWER (W) 10 -80 -90
05775-016
THD or THD + N (dB, Relative to Fundamental)
-10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90 0.001 0.1 THD 1 OUTPUT POWER (W) 10 -100
Figure 16. THD and THD + N vs. Output Power, 1 kHz Sine, 4 Load, PVDD = 12 V
100 0
Figure 19. THD and THD + N vs. Output Power, 1 kHz Sine, 4 Load, PVDD = 15 V
100 0 -10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90 THD
-10 10 -20 -30 1 -40 -50 0.1 -60 -70 THD + N 0.01 -80 -90 0.001 0.1 THD 1 OUTPUT POWER (W) 10 -100
THD or THD + N (dB, Relative to Fundamental)
05775-017
1 OUTPUT POWER (W)
10
Figure 17. THD and THD + N vs. Output Power, 1 kHz Sine, 6 Load, PVDD = 12 V
100 0
Figure 20. THD and THD + N vs. Output Power, 1 kHz Sine, 6 Load, PVDD = 15 V
100 0 -10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90
THD or THD + N (dB, Relative to Fundamental)
-10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90 0.001 0.1 THD 1 OUTPUT POWER (W) 10 -100
05775-018
1 OUTPUT POWER (W)
10
Figure 18. THD and THD + N vs. Output Power, 1 kHz Sine, 8 Load, PVDD = 12 V
Figure 21. THD and THD + N vs. Output Power, 1 kHz Sine, 8 Load, PVDD = 15 V
Rev. 0 | Page 10 of 24
05775-021
0.001 0.1
THD
-100
THD or THD + N (dB, Relative to Fundamental)
THD or THD + N (%)
THD or THD + N (%)
05775-020
0.001 0.1
-100
THD or THD + N (dB, Relative to Fundamental)
THD or THD + N (%)
THD or THD + N (%)
05775-019
0.001 0.1
-100
THD or THD + N (dB, Relative to Fundamental)
THD or THD + N (%)
THD or THD + N (%)
AD1994
100 0 100 0 -10 10 -20 -30 1 -40 -50 0.1 -60 -70 THD + N 0.01 THD 1 OUTPUT POWER (W) 10 -80 -90
05775-022
THD or THD + N (dB, Relative to Fundamental)
-10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90 0.001 0.1 THD 1 OUTPUT POWER (W) 10 -100
Figure 22. THD and THD + N vs. Output Power, 1 kHz Sine, 4 Load, PVDD = 18 V
100 0
Figure 25. THD and THD + N vs. Output Power, 1 kHz Sine, 4 Load, PVDD = 20 V
100 0 -10 10 -20 -30 1 -40 -50 0.1 -60 -70 THD + N 0.01 -80 -90
THD or THD + N (dB, Relative to Fundamental)
-10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90 0.001 0.1 THD 1 OUTPUT POWER (W) 10 -100
05775-023
1 OUTPUT POWER (W)
10
Figure 23. THD and THD + N vs. Output Power, 1 kHz Sine, 6 Load, PVDD = 18 V
100 0
Figure 26. THD and THD + N vs. Output Power, 1 kHz Sine, 6 Load, PVDD = 20 V
100 0 -10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90
THD or THD + N (dB, Relative to Fundamental)
-10 10 -20 -30 1 -40 -50 0.1 -60 -70 0.01 THD + N -80 -90 0.001 0.1 THD 1 OUTPUT POWER (W) 10 -100
05775-024
1 OUTPUT POWER (W)
10
Figure 24. THD and THD + N vs. Output Power, 1 kHz Sine, 8 Load, PVDD = 18 V
Figure 27. THD and THD + N vs. Output Power, 1 kHz Sine, 8 Load, PVDD = 20 V
Rev. 0 | Page 11 of 24
05775-027
0.001 0.1
THD
-100
THD or THD + N (dB, Relative to Fundamental)
THD or THD + N (%)
THD or THD + N (%)
05775-026
0.001 0.1
THD
-100
THD or THD + N (dB, Relative to Fundamental)
THD or THD + N (%)
THD or THD + N (%)
05775-025
0.001 0.1
-100
THD or THD + N (dB, Relative to Fundamental)
THD or THD + N (%)
THD or THD + N (%)
AD1994
50 45 100 90 80
OUTPUT POWER PER CHANNEL (W)
40
OUTPUT POWER (W)
35 30 25 20 15 10 5
05775-028
70 60 50 40 30 20 10
THD = 10%
THD = 10%
THD = 1%
THD = 1%
8
10
12
14
16
18
20
8
10
12
14
16
18
20
PVDD VOLTAGE (V)
PVDD VOLTAGE (V)
Figure 28. Maximum Power vs. PVDD, Stereo Mode, 4 Load
50 45
Figure 31. Maximum Power vs. PVDD, Mono Mode, 2 Load
100 90 80
OUTPUT POWER PER CHANNEL (W)
40
30 25 20 15 10 5 8 10 12 14 16 18 20
05775-029
OUTPUT POWER (W)
35
70 60 50 40 30 20 10 8 10 12 14 16 18 20
05775-032 05775-033
THD = 10%
THD = 10%
THD = 1%
THD = 1%
0
0
PVDD VOLTAGE (V)
PVDD VOLTAGE (V)
Figure 29. Maximum Power vs. PVDD, Stereo Mode, 6 Load
50 45
Figure 32. Maximum Power vs. PVDD, Mono Mode, 3 Load
100 90 80
OUTPUT POWER PER CHANNEL (W)
40
30 25 20 15 10 5 8 10 12 14 16 18 20
05775-030
OUTPUT POWER (W)
35
70 60 50 40 30 20 10 0 8 10 12 14 16 18 20 THD = 1% THD = 10%
THD = 10%
THD = 1%
0
PVDD VOLTAGE (V)
PVDD VOLTAGE (V)
Figure 30. Maximum Power vs. PVDD, Stereo Mode, 8 Load
Figure 33. Maximum Power vs. PVDD, Mono Mode, 4 Load
Rev. 0 | Page 12 of 24
05775-031
0
0
AD1994
100 90 80 2 x8 LOAD 100 90 80 1 x4 LOAD 1 x3 LOAD 1 x2 LOAD
POWER EFFICIENCY (%)
70 2 x4 LOAD 60 50 40 30 20 10
05775-034
POWER EFFICIENCY (%)
2 x6 LOAD
70 60 50 40 30 20 10
1 OUTPUT POWER PER CHANNEL (W)
10
1 OUTPUT POWER (W)
10
Figure 34. Power Efficiency vs. Output Power, Stereo Mode, PVDD = 12 V
4.0 3.5
Figure 37. Power Efficiency vs. Output Power, Mono Mode, PVDD = 12 V
8 7 1 x2 LOAD 6 5 4 1 x3 LOAD 3 2 1 x4 LOAD 1 0
ON-CHIP POWER DISSIPATION PER CHANNEL (W)
2 x4 LOAD 3.0 2.5 2.0 2 x6 LOAD 1.5 1.0 2 x8 LOAD 0.5 0
05775-035
ON-CHIP POWER DISSIPATION (W)
0
2
4
6
8
10
12
14
16
18
20
0
5
10
15
20
25
30
35
40
OUTPUT POWER PER CHANNEL (W)
OUTPUT POWER (W)
Figure 35. On-Chip Power Dissipation vs. Output Power, Stereo Mode, PVDD = 12 V
20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 20 200 250
Figure 38. On-Chip Power Dissipation vs. Output Power, Mono Mode, PVDD = 12 V
P-TYPE 25C N-TYPE 25C P-TYPE 130C N-TYPE 130C
PSRR (dB)
COUNT
150
100
50
05775-036
50
100
200
500
1k
2k
5k
10k
20k
05775-039
0 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 MOSFET ON-RESISTANCE (m)
FREQUENCY (Hz)
Figure 36. Power Supply Rejection Ratio (PSRR) vs. Frequency
Figure 39. Histogram Showing Manufacturing Variation of RDS-ON of the Output MOSFETS at 25C and 130C
Rev. 0 | Page 13 of 24
05775-038
05775-037
0 0.1
0 0.1
AD1994
100 90 80 2 x8 LOAD 2 x6 LOAD 2 x4 LOAD 60 50 40 30 20 10
05775-040
20 18
ON-CHIP POWER DISSIPATION (W)
16 14 12 10 8 6 4 2
1 x2 LOAD
POWER EFFICIENCY (%)
70
1 x3 LOAD 1 x4 LOAD
1
10
0
10
20
30
40
50
60
70
80
OUTPUT POWER PER CHANNEL (W)
OUTPUT POWER (W)
Figure 40. Power Efficiency vs. Output Power, Stereo Mode, PVDD = 18 V
10 9 100 90
Figure 42. On-Chip Power Dissipation vs. Output Power, Mono Mode, PVDD = 18 V
1 x4 LOAD
ON-CHIP POWER DISSIPATION PER CHANNEL (W)
8 7 6 5 4 3 2 1
05775-041
80
POWER EFFICIENCY (%)
2 x4 LOAD
1 x3 LOAD 1 x2 LOAD
70 60 50 40 30 20 10
2 x6 LOAD 2 x8 LOAD
0
5
10
15
20
25
30
35
40
1 OUTPUT POWER (W)
10
OUTPUT POWER PER CHANNEL (W)
Figure 41. On-Chip Power Dissipation vs. Output Power, Stereo Mode, PVDD = 18 V
Figure 43. Power Efficiency vs. Output Power, Mono Mode, PVDD = 18 V
Rev. 0 | Page 14 of 24
05775-042
0
0 0.1
05775-043
0 0.1
0
AD1994 THEORY OF OPERATION
OVERVIEW
The AD1994 is a 2-channel, high performance, switching, audio power amplifier. Each of the two - modulators converts a single-ended analog input into a 2-level pulse stream that controls the differential, full H-bridge, power output stage. The combination of an - modulator and a switching power stage provides an inherently linear and efficient means of amplifying the entire range of audio frequencies. The AD1994 also offers warning and protection circuits for overcurrent and overtemperature conditions, as well as silent turn-on and turn-off transitions. prolonged voltage clipping conditions, enabling stable operation at full modulation. The dynamic-order reduction circuit uses the high-order modulator, except during the crests of the highest waveform peaks. During these peaks, the quantization noise increases, but the SNR is still quite high. These modulator order transitions are fast and smooth enough to avoid audible artifacts. The modulator has a noise shaping effect, and SNR is increased in the audio band by shifting the quantization noise upward in frequency. For a nominal input clock frequency of 12.288 MHz, the noise floor rises sharply above 20 kHz. The actual clock frequency used in an application circuit can deviate from this rate by as much as 10%, and the corner frequency of the noise scales proportionately. The frequency at which the quantization noise dominates the output determines the amplifier's practical bandwidth. The expected transition rate at the output of a typical seventhorder, - modulator would be high enough to negate much of the efficiency benefit of a switching amplifier. However, the AD1994 incorporates a proprietary, dynamic, switching rate, reduction scheme that lowers that average switching frequency by approximately a factor of four. This results in slightly increased output energy between 450 kHz and 500 kHz and efficiency on par with other Class-D amplifiers. This low-Q spectral boost is an artifact of the noise shaping and is in no way related to the carrier frequency visible in the spectrum of PWM Class-D amplifiers.
- MODULATOR
The AD1994 is a switching type, also known as a Class-D, audio power amplifier. This class of amplifiers maximizes efficiency by only using its power output devices in full-on or full-off states. While most Class-D amplifiers use some variation of pulse-width modulation (PWM), the AD1994 uses - modulation to determine the switching pattern of the output devices. This provides a number of important benefits. - modulators do not produce a sharp peak with many harmonics in the AM frequency band as pulse-width modulators (PWM) often do. In addition, the 1-bit quantizer produces excellent linearity across the full amplitude range. - modulators require feedback to generate an error signal with respect to the input. The feedback voltages for the AD1994 modulators come from the outputs of the power devices and before the passive low-pass filters (see Figure 45). This compensates for nonlinear behavior in the power stage, such as nonoverlap time, mismatched rise and fall times, and propagation delays. It also reduces sensitivity to both dc and transient changes of the power supply voltage. - modulators operate in discrete time. As with all timequantized systems, the Nyquist frequency is equal to half of the sampling frequency and input signals above that point aliases back into the base band. The AD1994 sampling frequency (master clock) is equal to half the frequency of the input clock, approximately 6 MHz, so images only alias for input frequencies above approximately 3 MHz. This is far enough above the audio band that bandwidth and aliasing are not a problem in real applications. The AD1994 implements a seventh-order, - modulator with a 1-bit quantizer. Traditionally, higher-order designs such as this are not suitable for driving a Class-D amplifier because of stability problems at higher modulation factors. The modulator design of the AD1994 is unusual in that it is stable to 90% modulation. To allow the amplifier to drive even further, the AD1994 dynamically reverts from seventh order to second order above a fixed modulation threshold. The second-order modulator is unconditionally stable, including during
MUTE AND RESET
When power is applied and the RESET pin remains asserted, the AD1994 is in its lowest power consumption mode. The analog modulator is not running, and the power stage is tristated. On deasserting the RESET pin, the modulator begins a start-up sequence that includes initialization of the modulator, the protection circuits, and other functions. Once the start-up sequence is complete, the amplifier is in a state in which the modulator is running, but the output stage is not driven. When MUTE is deasserted, the output is started using a soft-start sequence that avoids any audible pop or click noise in the output signal. The output power transistors do not switch while MUTE remains asserted. Unlike the analog mute circuits found on some amplifiers that can be limited in their attenuation by the control logic or crosstalk, the mute attenuation on the AD1994 is greater than its dynamic range. The noise floor of the output signal also drops while in MUTE because the output transistors are not switching.
Rev. 0 | Page 15 of 24
AD1994
Power-Up Sequencing
Careful power-up is necessary when using the AD1994 to ensure correct operation and to avoid possible latch-up issues. The AD1994 should be powered up with RESET and MUTE held low until all the power supplies have stabilized. Once the supplies have stabilized, bring the AD1994 out of RESET by bringing RESET high. Begin the soft unmute sequence by bringing MUTE high at least 1 sec after the RESET rising edge. The amplifier produces audio using a shorter start-up sequence (as shown in Table 7), but the amplifier can produce an audible pop or click noise as the output starts switching. This is because the ac coupling capacitors at the analog input have a long time constant. If MUTE is deasserted substantially less than 1 sec after deasserting RESET, then these capacitors may not have charged to a steady state. They need ample time to settle at a bias voltage of VREF, the reference voltage for the single-ended inputs, or the amplifier starts with a slight dc offset. When the load impedance is substantially less than 4 , the system would be current limited if configured for normal stereo operation, and the amplifier would enter the overcurrent error state when a nominal input signal is applied. Under these conditions, the amount of real power delivered to the load increases in mono mode. The minimum recommended impedance in mono mode is 2 (as compared to 4 for stereo operation), so the effective power delivered to a single channel can be as much as twice the maximum achievable in stereo mode. For reactive loads, the impedance can only be below the recommended threshold over a small portion of the amplifier's bandwidth. In these cases, the amplifier can enter overcurrent shutdown in response to even small input signals in those frequency bands. When designing a system, use the minimum load impedance over the entire range of amplified frequencies when calculating current output rather than the average or nominal load impedance ratings often cited by loudspeaker driver manufacturers.
MODULATOR MODE
The AD1994 is capable of operating as a modulator for controlling external power devices. When MOD_EN (Pin 49) is logic level high at the rising edge of RESET, both the left and right internal power stages are disabled. The error output flags (ERR2, ERR1, and ERR0) and the nonoverlap delay inputs (DCNTL2, DCNTL1, and DCNTL0) no longer have meaning because they apply only to the internal power stages. The logic level outputs from the two modulators appear on Pin 19 (MODL) and Pin 20 (MODR).
MONO MODE
The power supply voltage and the limited current that the output transistors can source combine to dictate that maximum total output power of the AD1994. For higher impedance loads, the system is voltage limited, and for lower impedance loads, the system is current limited. In normal stereo operation, each output is driven by four MOSFET devices arranged in a full H-bridge configuration, also known as bridge-tied load (BTL). This provides the maximum differential output voltage swing, equal to twice the voltage of the power supply. However, operating in mono mode doubles the maximum achievable output current. When MONO_EN (Pin 64) is logic level high at the rising edge of RESET, the right channel modulator is disabled, and the left channel modulator is used to drive both the left and right output stages in parallel. When using mono mode, connect OUTL+ directly to OUTR+, connect OUTL- directly to OUTR-, and use the combined differential pair to a drive a single load. Connect the feedback pair to the positive and negative feedback input of the left modulator. The right channel feedback pins are unused in mono mode. The RDS-ON of the power FETs drops to half of its value in stereo operation because the devices are in parallel, and the AD1994 delivers its full current capability to a single channel. Note that the practical effect of mono mode depends greatly on the load impedance. If the load is 4 or greater, the efficiency of the amplifier increases due to the reduced effective resistance of power FETs, and the amplifier dissipates less heat. However, the amount of real power delivered to the load does not increase because the system is voltage limited (that is, the output waveform voltage clips before current limiting occurs).
GAIN STRUCTURE
Analog Input Levels
The AD1994 has single-ended inputs for the left and right channels. The analog input section uses an internal amplifier to bias the input signal to the reference level, VREF, which is nominally equal to AVDD/2. A dc-blocking capacitor, as shown in Figure 44, prevents this bias voltage from affecting the signal source. In combination with the nominal 20 k input impedance, the value of this capacitor should be large enough to produce a flat frequency response at the lowest input frequency of interest. Note that the amplifier is capable of dc-coupled operation if the circuit includes some means to account for this bias voltage.
0V
+
AINL/ AINR
05775-044
Figure 44. AC-Coupled Input Signal
Rev. 0 | Page 16 of 24
AD1994
Setting the Modulator Gain
The AD1994 modulator uses a combination of the input signal and feedback from the power output stage to calculate its twostate output pattern. The feedback input nodes are part of the internal analog circuit that operates from the AVDD (nominal 5 V) power supply. Because the voltage measured at the power outputs is nominally between 0 V and PVDD, and thus beyond the 0 V to AVDD range, a voltage divider is required to scale the feedback to an appropriate level. Resistor voltage dividers should sense the voltage on each side of the differential output and provide these feedback signals to the modulator, as shown in Figure 45.
PVDD EXTERNAL COMPONENTS PVDD
Programmable Gain Amplifier (PGA)
The - modulator itself requires a fixed gain for a given value of PVDD to maintain optimal stability. This gain can be appropriate, but many applications require more gain to account for low source signal levels. The AD1994 includes a programmable gain amplifier (PGA) to boost the overall amplifier gain. PGA1 (Pin 31) and PGA0 (Pin 32) select one of four PGA gain values, as shown in Table 11.
Table 11. PGA Gain Settings
PGA1 0 0 1 1 PGA0 0 1 0 1 PGA Gain (dB) 0 6 12 18
D1 OUTx+ D2 PGND NFx+ R2 R1
L C
RL C
L R3
D3 OUTx- D4 PGND NFx- R4
05775-045
The AD1994 incorporates a single-ended-to-differential converter for each channel in the analog front-end section. The PGA is also part of this analog front-end, and it affects the analog input signal before it enters the - modulator. The PGA1 and PGA0 pins are continuously monitored and allow the gain to be changed at any time.
Figure 45. H-Bridge Configuration
POWER STAGE
The H-Bridge
The output stage of the AD1994 includes four integrated MOSFET devices arranged in a full H-bridge, as shown in Figure 45. The P-Type, high-side transistor of one leg and the N-Type, low-side transistor of the opposite leg switch on and off as a pair producing a total voltage swing across the load of -PVDD to +PVDD. The drive is floating and differential, and it is important that neither output terminal be shorted to ground. The power supply for the output stage of the AD1994, PVDD, should be in the 8 V to 20 V range and should be capable of supplying enough current to drive the load. Connect the power supply across the PVDD and PGND pins. The feedback pins, NFR+, NFR-, NFL+, and NFL-, supply negative feedback to the modulator as described in the Setting the Modulator Gain section.
The resistor values should satisfy the following equation to maintain modulator stability.
Gain =
R1 + R2 R3 + R 4 PVDD = = 3.635 R2 R4
Selecting a gain that meets this criterion ensures that the modulator remains in a stable operating condition. The ratio of the resistances sets the gain rather than the absolute values. However, the dividers provide a path from the high voltage supply to ground; therefore, the values should be large enough to produce negligible loss due to quiescent current. The chip contains a calibration circuit to minimize voltage offsets at the speaker, which helps to minimize clicks and pops when muting or unmuting. Optimal performance is achieved for the offset calibration circuit when the feedback divider resistors sum to 6 k, that is, (R1 + R2) = 6 k, and (R3 + R4) = 6 k.
Table 10. Recommended Feedback Resistor Values
PVDD (V) 12 15 18 20 R1 (k) 4.2 4.55 4.8 4.91 R2 (k) 1.8 1.45 1.2 1.09 Gain 3.3 (+10.4 dB) 4.1 (+12.3 dB) 5.0 (+14.0 dB) 5.5 (+14.8 dB)
Rev. 0 | Page 17 of 24
AD1994
Output Transistor Nonoverlap Time
The AD1994 allows the user to select from one of eight different nonoverlap times, as shown in Figure 46. Nonoverlap time prevents or minimizes the period during which both the highside and low-side devices are on simultaneously due to propagation delays and nonzero rise and fall times. If both the upper and lower portions of a half-bridge conduct simultaneously, there is a path directly from the power supply to ground and an induced current flow known as shoot-through. However, introducing this delay increases distortion by pushing the switching pattern further from an ideal two-state waveform. Selecting the nonoverlap delay requires a compromise between distortion and efficiency. The logic levels on the three delay control pins, DCTRL2, DCTRL1, and DCTRL0, set the nonoverlap time according to Table 12. The state of DCTRL[2:0] is read on the rising edge of RESET and should not be changed while RESET is logic high.
Table 12. Nonoverlap Time Settings
DCTRL2 0 0 0 0 1 1 1 1
1
As mentioned in the - Modulator section, the modulator has a noise-shaping effect such that SNR is increased within the audio band by shifting modulator quantization noise upward in frequency. For external clock frequency of 12.288 MHz, the modulator's noise-shaping works in a manner that results in a flat noise floor at the amplifier output for frequencies 20 kHz and below. Above 20 kHz, the amplifier noise rises due to the spectral shaping of the modulator quantization noise. At very high frequencies, the noise floor levels off and decreases due to poles in the modulator noise-transfer function and in the external LC filter. The clock frequency does not have to be exactly equal to 12.288 kHz and can vary by up to 10%. For other rates, the noise corner scales linearly with frequency. When the modulator runs at a rate lower than nominal, the average power stage switching frequency decreases, the efficiency increases slightly, and the noise floor begins to rise at a slightly lower frequency. Likewise, a faster clock gives slightly increased bandwidth and slightly lower efficiency.
DCTRL1 0 0 1 1 0 0 1 1
DCTRL0 0 1 0 1 0 1 0 1
Nonoverlap Time (ns)1 62 49 37 24 15 13.5 12 9
Using a Crystal Oscillator
The AD1994 can use a crystal connected to the CLKI and CLKO pins as a master clock source, as shown in Figure 47. The CLKI and CLKO pins connect to an internal inverter to create a full resonator. The typical values shown work in many applications, but the crystal manufacturer should provide the exact type and value of the capacitors and the resistor.
22pF XTAL 47 22pF
Values are typical and are not production tested.
HIGH-SIDE GATE DRIVE LOW-SIDE GATE DRIVE
05775-046
CLKO
CLKI
tNOL
tNOL
Figure 47. Crystal Connection
Figure 46. Half-Bridge Nonoverlap Delay Timing
Using an External Clock Source
If a clock signal of the appropriate frequency already exists in the application circuit, connect it directly to CLKI and leave CLKO floating. The logic levels of the square wave should be compatible with those defined in Specifications section. Large amounts of jitter on the clock input degrade performance. Whenever possible, avoid passing the clock signal though programmable logic and other circuits with unknown or variable propagation delay. In general, clock signals suitable for audio ADCs or DACs are also appropriate for use with the AD1994.
The shortest setting (DCTRL[2:0] = 111) or the second shortest setting (DCTRL[2:0] = 111) is recommended for most applications. These two settings allow a small trade-off between efficiency and distortion. Longer nonoverlap times generally increase distortion while providing little or no decrease in shootthrough current.
CLOCKING
The AD1994 - modulator requires an external clock source with a nominal frequency of 12.288 MHz. This clock can come from a crystal or from an existing clock signal in the application circuit. The discrete time portions of the modulator run internally at 6.144 MHz, corresponding to 128 x fS, where fS = 48 kHz.
Rev. 0 | Page 18 of 24
05775-047
AD1994
Clocking Multiple Amplifiers in Parallel
If there are multiple AD199x family amplifiers connected to the same PVDD supply, use the same clock source (or synchronous derivatives) for each amplifier as previously described. Avoid clocking amplifiers from similar but asynchronous clocks if they use the same power supply because this can result in beat frequencies.
Overcurrent Protection
The AD1994 features over current or short-circuit protection. If the current through any power transistors exceeds approximately 4 A, the part enters a mute state and the overcurrent error output (ERR0) is asserted. This is a latched error and does not clear automatically. Restore normal operation and clear the error condition by either asserting and then negating RESET or by asserting and then negating MUTE.
PROTECTION CIRCUITS AND ERROR REPORTING
Thermal Protection
The AD1994 features thermal protection. When the die temperature exceeds approximately 135C, the thermal warning error output (ERR1) is asserted. If the die temperature exceeds approximately 150C, the thermal shutdown error output (ERR2) is asserted. If this occurs, the part shuts down to prevent damage to the part. When the die temperature drops below approximately 120C, the part returns to normal operation automatically and negates both error outputs.
Rev. 0 | Page 19 of 24
AD1994 APPLICATION CIRCUITS
DVDD 0.1F + 47F AVDD 0.1F + 47F 1000F PVDD + 1000F PVDD + 0.1F 0.1F
AVDD
DVDD
PVDD1
PVDD2
PVDD L
10F
+
AINL
OUTL+ R1 NFL+ C
10F
+
AINL
R2
R2 NFL- 6.8F + MOD_FILT 10k OUTL- PVDD R1 L
AD1994
REF_FILT 4.7F + 0.1F OUTR+ R1 PGA0 PGA1 DCTRL2 DIGITAL INPUTS DCTRL1 DCTRL0 MUTE RESET THERMAL SHUTDOWN THERMAL WARNING OVERCURRENT ERR2 ERR1 ERR0 CLKI OUTR- R2 NFR- PVDD R1 NFR+ R2 PVDD
C
L C
L
C
R1 = 4.2k R2 = 1.8k L = 18H C = 1F LOAD = 6
PGND1
CLKO
PGND2
AGND
DGND
Figure 48. Typical Stereo Circuit
Rev. 0 | Page 20 of 24
05775-048
AD1994 OUTLINE DIMENSIONS
9.00 BSC SQ 0.60 MAX 0.60 MAX
48 49 PIN 1 INDICATOR
0.30 0.25 0.18
64 1
PIN 1 INDICATOR
TOP VIEW
8.75 BSC SQ
EXPOSED PAD
(BOTTOM VIEW)
7.25 7.10 SQ 6.95
0.45 0.40 0.35
33
32
17 16
1.00 0.85 0.80
12 MAX
0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.50 BSC 0.20 REF
7.50 REF
0.25 MIN
SEATING PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4
Figure 49. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 9 mm x 9 mm Body, Very Thin Quad (CP-64-3) Dimension shown in millimeters
ORDERING GUIDE
Model AD1994ACPZ 1 AD1994ACPZRL1 AD1994ACPZRL71 EVAL-AD1994EB
1
Temperature Range -40C to +85C -40C to +85C -40C to +85C
Package Description 64-Lead Lead Frame Chip Scale Package (LFCSP_VQ) 64-Lead Lead Frame Chip Scale Package (LFCSP_VQ), 13" Tape and Reel 64-Lead Lead Frame Chip Scale Package (LFCSP_VQ), 7" Tape and Reel Evaluation Board
122105-0
Package Option CP-64-3 CP-64-3 CP-64-3
Z = Pb-free part.
Rev. 0 | Page 21 of 24
AD1994 NOTES
Rev. 0 | Page 22 of 24
AD1994 NOTES
Rev. 0 | Page 23 of 24
AD1994 NOTES
(c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05775-0-2/06(0)
Rev. 0 | Page 24 of 24

▲Up To Search▲

Price & Availability of EVAL-AD1994EB

	To Download EVAL-AD1994EB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .